Difference between revisions of "DPSI BUS HUB"
| Line 26: | Line 26: | ||
File:HUB-3 02.jpg|BUS HUB-3 cable | File:HUB-3 02.jpg|BUS HUB-3 cable | ||
</gallery> | </gallery> | ||
| + | |||
| + | ==Connections diagram== | ||
| + | [[File:A15060 04.jpg|640x400.jpg|640px|thumb|none|Bus connectors DPSI BUS HUB]] | ||
| + | {| class="wikitable" | ||
| + | |+align="bottom"|''Table 1: Bus connectors DPSI BUS HUB'' | ||
| + | |- | ||
| + | !Connector | ||
| + | !Description | ||
| + | |- | ||
| + | |1 | ||
| + | |Bus connection cable with sockets to connect wing plugs | ||
| + | |- | ||
| + | |2 | ||
| + | |Hub2 bus cable to connect bus servos | ||
| + | |} | ||
==Optionale Doppelstromversorgung und geregelte Eingangsspannung== | ==Optionale Doppelstromversorgung und geregelte Eingangsspannung== | ||
| Line 43: | Line 58: | ||
===Doppelstromversorgung mit DPSI Ampere=== | ===Doppelstromversorgung mit DPSI Ampere=== | ||
Inhalte folgen... | Inhalte folgen... | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
==Specifications== | ==Specifications== | ||
Revision as of 09:07, 26 October 2015
Contents
Product description
The DPSI BUS HUB is a digital bus distribution module which can feed through common sum signals. It is equipped with the connectors and can be extended if desired. The DPSI BUS HUB ensures connections of approx. ten bus servos without soldering. The servos can be connected with the HUB-2 and HUB-3 plug system or with latching Bus wing plugs and sockets to the DPSI BUS HUB.
Connections and wiring
Wing wiring
The connection to the wings is made with 12in long silicon cables with latching wing plugs. For thin wing profiles inside the wings the Bus wing plugs for 2 or 3 servos can be used. With thick wing profiles alternatively the Bus wing cable with plug can be used. Then servo connection is made with Servo SinglePorts.
Bus wing plug for 2 servos
Bus wing cable with plug
Mounted Servo SinglePorts
Fuselage wiring
Servos inside the fuseslage's backside can be connected to a 47in integrated HUB-2 cable. Further servos can be connected with additional BUS HUB-2 or BUS HUB-3 cables.
BUS HUB cable
BUS HUB cable
BUS HUB-2 cable
BUS HUB-3 cable
Connections diagram
| Connector | Description |
|---|---|
| 1 | Bus connection cable with sockets to connect wing plugs |
| 2 | Hub2 bus cable to connect bus servos |
Optionale Doppelstromversorgung und geregelte Eingangsspannung
Der DPSI BUS HUB kann mit folgenden DPSI-Doppelstromversorgungen betrieben werden:
- DPSI Micro DualBat Serie
- DPSI Ampere optional mit oder ohne Spannungsregler DPSI Voltage
Doppelstromversorgung mit DPSI Micro DualBat
Um den DPSI BUS HUB mit einer DPSI Micro DualBat und zwei überwachten Akkus mit Strom zu versorgen, müssen zwei Akkus an den Akkueingängen "Bat.1" und "Bat.2" angeschlossen werden. Die DPSI Micro DualBat Doppelstromversorgung wird mit dem "RV OUT" Ausgang am DPSI BUS HUB am Eingang "BAT" angeschlossen.
Die folgenden DPSI Micro DualBat Doppelstromversorgungen eignen sich zum betreiben des DPSI BUS HUB:
- DPSI Mirco DualBat 5.5V/5.9V MPX-1xMPX
- DPSI Mirco DualBat 5.9V/7.2V MPX-1xMPX
Neben der sicherheitsbedingten Doppelstromversorgung ermöglicht die DPSI Micro DualBat auch die Versorgung mit einer geregelten Eingangsspannung von 5,5 Volt, 5,9 Volt oder 7,2 Volt.
Doppelstromversorgung mit DPSI Ampere
Inhalte folgen...
Specifications
| Input voltage | 6V - 8.4V (5 NiMH or 2S Li++) |
| Output voltage (regulated for RX output) | 5.9V |
| Ampacity (RX output) | Permanent 2A, Peak 10A @ 2S LiPo battery |
| Output voltage (unregulated for servos) | Identical to the input voltage |
| Ampacity (unregulated output) | Permanent 8A, Peak 16A |
| Power-on control | LED |
| Quiescent current | approx. 3.5mA @ 7.4V |
| Max. amount servos | 10 |
| Dimensions | 50mm x 39mm x 14mm |
| Weight | approx. 86 Gramm |
