Difference between revisions of "DPSI BUS HUB"

From Hacker Motor Wiki
Jump to: navigation, search
(Optionale Doppelstromversorgung und geregelte Eingangsspannung)
(Optionale Doppelstromversorgung und geregelte Eingangsspannung)
Line 42: Line 42:
 
|}
 
|}
  
==Optionale Doppelstromversorgung und geregelte Eingangsspannung==
+
==Optional dual power supply and regulated input voltage==
Der DPSI BUS HUB kann mit folgenden DPSI-Doppelstromversorgungen betrieben werden:
+
The DPSI BUS HUB can be operated with the listed DPSI dual power supplies:
* [[DPSI Micro DualBat|DPSI Micro DualBat Serie]]
+
* [[DPSI Micro DualBat|DPSI Micro DualBat series]]
* [[DPSI Ampere]] optional mit oder ohne Spannungsregler [[DPSI Voltage]]
+
* [[DPSI Ampere]] optionally with or without voltage regulator [[DPSI Voltage]]
  
 
===Doppelstromversorgung mit dem DPSI Micro DualBat===
 
===Doppelstromversorgung mit dem DPSI Micro DualBat===
Um den DPSI BUS HUB mit einer DPSI Micro DualBat und zwei überwachten Akkus mit Strom zu versorgen, müssen zwei Akkus an den Akkueingängen "Bat.1" und "Bat.2" der DPSI Micro DualBat angeschlossen werden. Die DPSI Micro DualBat Doppelstromversorgung wird  mit dem "RV OUT" Ausgang am DPSI BUS HUB am Eingang "BAT" angeschlossen.
+
For operating the DPSI BUS HUB with a DPSI Micro DualBat and two monitored batteries two batteries must be connected to the battery inputs "Bat.1" and "Bat.2" of the DPSI Micro DualBat. The DPSI Micro DualBat dual power supply must be connected with the "RV OUT" output to the DPSI BUS HUB input "BAT".
  
 
Die folgenden DPSI Micro DualBat Doppelstromversorgungen eignen sich zum betreiben des DPSI BUS HUB:
 
Die folgenden DPSI Micro DualBat Doppelstromversorgungen eignen sich zum betreiben des DPSI BUS HUB:

Revision as of 09:26, 26 October 2015

Product description

DPSI BUS HUB

The DPSI BUS HUB is a digital bus distribution module which can feed through common sum signals. It is equipped with the connectors and can be extended if desired. The DPSI BUS HUB ensures connections of approx. ten bus servos without soldering. The servos can be connected with the HUB-2 and HUB-3 plug system or with latching Bus wing plugs and sockets to the DPSI BUS HUB.

Connections and wiring

Wing wiring

The connection to the wings is made with 12in long silicon cables with latching wing plugs. For thin wing profiles inside the wings the Bus wing plugs for 2 or 3 servos can be used. With thick wing profiles alternatively the Bus wing cable with plug can be used. Then servo connection is made with Servo SinglePorts.

Fuselage wiring

Servos inside the fuseslage's backside can be connected to a 47in integrated HUB-2 cable. Further servos can be connected with additional BUS HUB-2 or BUS HUB-3 cables.

Connections diagram

Bus connectors DPSI BUS HUB
Table 1: Bus connectors DPSI BUS HUB
Connector Description
1 Bus connection cable with sockets to connect wing plugs
2 Hub2 bus cable to connect bus servos

Optional dual power supply and regulated input voltage

The DPSI BUS HUB can be operated with the listed DPSI dual power supplies:

Doppelstromversorgung mit dem DPSI Micro DualBat

For operating the DPSI BUS HUB with a DPSI Micro DualBat and two monitored batteries two batteries must be connected to the battery inputs "Bat.1" and "Bat.2" of the DPSI Micro DualBat. The DPSI Micro DualBat dual power supply must be connected with the "RV OUT" output to the DPSI BUS HUB input "BAT".

Die folgenden DPSI Micro DualBat Doppelstromversorgungen eignen sich zum betreiben des DPSI BUS HUB:

  • DPSI Mirco DualBat 5.5V/5.9V MPX-1xMPX
  • DPSI Mirco DualBat 5.9V/7.2V MPX-1xMPX

Neben der sicherheitsbedingten Doppelstromversorgung ermöglicht die DPSI Micro DualBat auch die Versorgung mit einer geregelten Eingangsspannung von 5,5 Volt, 5,9 Volt oder 7,2 Volt. Der DPSI BUS HUB kann mit dem in die DPSI Micro DualBat integrierten Magentschalter ein- und ausgeschaltet werden.

Der DPSI BUS HUB in Verbindung mit der DPSI Micro DualBat wird für Flugmodelle mit bis zu ca. acht Servos bei einem Dauerstrom von ca. 4 Ampere empfohlen.

Doppelstromversorgung mit der DPSI Ampere

Um den DPSI BUS HUB mit einer DPSI Ampere und zwei überwachten Akkus mit Strom zu versorgen, müssen zwei Akkus an den Akkueingängen "Battery 1" und "Battery 2" der DPSI Ampere angeschlossen werden. Die DPSI Ampere Doppelstromversorgung wird mit dem "Vout" Ausgang am DPSI BUS HUB am Eingang "BAT" angeschlossen.

Neben der sicherheitsbedingten Doppelstromversorgung ermöglicht die DPSI DPSI Ampere das Ein- und Ausschalten des DPSI BUS HUB mit dem in die DPSI Ampere integrierten Magentschalter.

Wird eine zusätzliche Spannungsregelung benötigt, kann zusätzlich der DPSI Voltage Spannungsregler benutzt werden. Die DPSI Voltage wird auf den "Vout" und "Charge" Anschluss der DPSI Ampere aufgesteckt, mit dem "Reg. out" Ausgang wird die DPSI Voltage am DPSI BUS HUB am Eingang "BAT" angeschlossen. Mit dem Jumper "Reg. out" kann eine geregelte Ausgangsspannung von 6,0 Volt, 6,6 Volt oder 7,2 Volt eingestellt werden.

Specifications

Table 2: Specifications DPSI BUS HUB
Input voltage 6V - 8.4V (5 NiMH or 2S Li++)
Output voltage (regulated for RX output) 5.9V
Ampacity (RX output) Permanent 2A, Peak 10A @ 2S LiPo battery
Output voltage (unregulated for servos) Identical to the input voltage
Ampacity (unregulated output) Permanent 8A, Peak 16A
Power-on control LED
Quiescent current approx. 3.5mA @ 7.4V
Max. amount servos 10
Dimensions 50mm x 39mm x 14mm
Weight approx. 86 Gramm