Difference between revisions of "DPSI BUS HUB"

From Hacker Motor Wiki
Jump to: navigation, search
(Product description)
 
(14 intermediate revisions by one other user not shown)
Line 4: Line 4:
 
[[File:A15060 00.jpg|640x400.jpg|350px|thumb|none|DPSI BUS HUB]]
 
[[File:A15060 00.jpg|640x400.jpg|350px|thumb|none|DPSI BUS HUB]]
  
The DPSI BUS HUB is a digital bus distribution module which can feed through common sum signals. It is equipped with the connectors and can be extended if desired.
+
The DPSI BUS HUB is a digital bus distribution module which can handle common sum signals. It is equipped with the connectors and can be extended if desired.
 
The DPSI BUS HUB ensures connections of approx. '''ten bus servos''' without soldering. The servos can be connected with the '''HUB-2 and HUB-3''' plug system or with '''latching Bus wing plugs and sockets''' to the DPSI BUS HUB.
 
The DPSI BUS HUB ensures connections of approx. '''ten bus servos''' without soldering. The servos can be connected with the '''HUB-2 and HUB-3''' plug system or with '''latching Bus wing plugs and sockets''' to the DPSI BUS HUB.
  
 
==Connections and wiring==
 
==Connections and wiring==
===Flächen-Verkabelung===
+
===Wing wiring===
Der Anschluss zu den Flächen erfolgt über 30cm lange Silikonkabel mit verriegelbaren Flächensteckern. Bei dünnen Flächenprofilen können in den Tragflächen die '''Bus-Flächenstecker für 2 bzw. 3 Servos''' eingesetzt werden.  
+
The connection to the wings is made with 12in long silicon cables with latching wing plugs. For thin wing profiles inside the wings the '''Bus wing plugs for 2 or 3 servos''' can be used.
 
+
With thick wing profiles alternatively the '''Bus wing cable with plug''' can be used. Then servo connection is made with [[Servo SinglePort|Servo SinglePorts]].
Alternativ können bei dickeren Flächenprofilen auch die '''Bus-Flächenkabel mit Stecker''' zum Einsatz kommen. Der Servoanschluss erfolgt hierbei über [[Servo SinglePort|Servo SinglePorts]].
 
 
 
 
<gallery>
 
<gallery>
  File:R88840002 01.jpg|Bus-Flächenstecker für 2 Servos
+
  File:R88840002 01.jpg|Bus wing plug for 2 servos
  File:RF1686 01.jpg|Bus-Flächenkabel mit Stecker
+
  File:RF1686 01.jpg|Bus wing cable with plug
  File:A12120 08.jpg|Montierte Servo SinglePorts
+
  File:A12120 08.jpg|Mounted Servo SinglePorts
 
</gallery>
 
</gallery>
  
===Rumpf-Verkabelung===
+
===Fuselage wiring===
Servos im hinteren Rumpfteil werden an ein 120cm langes integrierte HUB-2 Kabel angeschlossen, weitere Servos können über zusätzliche '''HUB-2 oder HUB-3-Kabel''' angeschlossen werden.
+
Servos inside the fuseslage's backside can be connected to a 47in integrated HUB-2 cable. Further servos can be connected with additional '''BUS HUB-2 or BUS HUB-3 cables.'''
  
 
<gallery>
 
<gallery>
  File:HUB-2 01.jpg|BUS HUB-Kabel
+
  File:HUB-2 01.jpg|BUS HUB cable
  File:HUB-2 04.jpg|BUS HUB-Kabel
+
  File:HUB-2 04.jpg|BUS HUB cable
  File:HUB-2 02.jpg|BUS HUB-2-Kabel
+
  File:HUB-2 02.jpg|BUS HUB-2 cable
  File:HUB-3 02.jpg|BUS HUB-3-Kabel
+
  File:HUB-3 02.jpg|BUS HUB-3 cable
 
</gallery>
 
</gallery>
  
Line 32: Line 30:
 
[[File:A15060 04.jpg|640x400.jpg|640px|thumb|none|Bus connectors DPSI BUS HUB]]
 
[[File:A15060 04.jpg|640x400.jpg|640px|thumb|none|Bus connectors DPSI BUS HUB]]
 
{| class="wikitable"
 
{| class="wikitable"
|+align="bottom"|''Tabelle 1: Bus connectors DPSI BUS HUB''
+
|+align="bottom"|''Table 1: Bus connectors DPSI BUS HUB''
 
|-
 
|-
 
!Connector
 
!Connector
Line 43: Line 41:
 
|Hub2 bus cable to connect bus servos
 
|Hub2 bus cable to connect bus servos
 
|}
 
|}
 +
 +
==Optional dual power supply and regulated input voltage==
 +
The DPSI BUS HUB can be operated with the listed DPSI dual power supplies:
 +
* [[DPSI Micro DualBat|DPSI Micro DualBat series]]
 +
* [[DPSI Ampere]] optionally with or without voltage regulator [[DPSI Voltage]]
 +
 +
===Dual power supply with the DPSI Micro DualBat===
 +
For operating the DPSI BUS HUB with a DPSI Micro DualBat and two monitored batteries two batteries must be connected to the battery inputs "Bat.1" and "Bat.2" of the DPSI Micro DualBat. The DPSI Micro DualBat dual power supply must be connected with the "RV OUT" output to the DPSI BUS HUB input "BAT".
 +
 +
The listed DPSI Bicro DualBat dual power Supplies are suitable for operating the DPSI BUS HUB:
 +
* DPSI Mirco DualBat 5.5V/5.9V MPX-1xMPX
 +
* DPSI Mirco DualBat 5.9V/7.2V MPX-1xMPX
 +
 +
In addition to the safety-related dual power supply the DPSI Micro DualBat allows operating with a regulated input voltage of 5.5 volts, 5.9 volts or 7.2 volts. The DPSI BUS HUB can be switched on and off with the magnetic switch integrated inside the DPSI Micro DualBat.
 +
 +
<div class="hint">The DPSI BUS HUB connected with the DPSI Micro DualBat is recommended for R/C models with up to approx. eight servos at a permanent current of approx. 4 ampere.</div>
 +
 +
===Dual power supply with the DPSI Ampere===
 +
For operating the DPSI BUS HUB with a DPSI Ampere and two monitored batteries two batteries must be connected to the battery inputs "Battery 1" and "Battery 2" of the DPSI Ampere. The DPSI Micro DualBat dual power supply must be connected with the "Vout" output to the DPSI BUS HUB input "BAT".
 +
 +
In addition to the safety-related dual power supply the DPSI Ampere allows switching on and off the DPSI BUS HUB with the magnetic switch integrated inside the DPSI Ampere.
 +
 +
If an additional voltage regulation is needed optionally the voltage regulator DPSI Voltage can be used. The DPSI Voltage must be connected to the DPSI Ampere's  "Vout" and "Charge" connectors, the DPSI Voltage's "Reg. out" output must be connecetd to teh DPSI BUS HUB's "BAT" input. With the jumper "Reg. out" a regulated input voltage of 6.0 volts, 6.6 volts or 7.2 volts can be selected.
  
 
==Specifications==
 
==Specifications==
 
{| class="wikitable"
 
{| class="wikitable"
|+align="bottom"|''Table 1: Specifications DPSI BUS HUB''
+
|+align="bottom"|''Table 2: Specifications DPSI BUS HUB''
 
|-
 
|-
 
|Input voltage
 
|Input voltage

Latest revision as of 15:42, 27 November 2015

Product description

DPSI BUS HUB

The DPSI BUS HUB is a digital bus distribution module which can handle common sum signals. It is equipped with the connectors and can be extended if desired. The DPSI BUS HUB ensures connections of approx. ten bus servos without soldering. The servos can be connected with the HUB-2 and HUB-3 plug system or with latching Bus wing plugs and sockets to the DPSI BUS HUB.

Connections and wiring

Wing wiring

The connection to the wings is made with 12in long silicon cables with latching wing plugs. For thin wing profiles inside the wings the Bus wing plugs for 2 or 3 servos can be used. With thick wing profiles alternatively the Bus wing cable with plug can be used. Then servo connection is made with Servo SinglePorts.

Fuselage wiring

Servos inside the fuseslage's backside can be connected to a 47in integrated HUB-2 cable. Further servos can be connected with additional BUS HUB-2 or BUS HUB-3 cables.

Connections diagram

Bus connectors DPSI BUS HUB
Table 1: Bus connectors DPSI BUS HUB
Connector Description
1 Bus connection cable with sockets to connect wing plugs
2 Hub2 bus cable to connect bus servos

Optional dual power supply and regulated input voltage

The DPSI BUS HUB can be operated with the listed DPSI dual power supplies:

Dual power supply with the DPSI Micro DualBat

For operating the DPSI BUS HUB with a DPSI Micro DualBat and two monitored batteries two batteries must be connected to the battery inputs "Bat.1" and "Bat.2" of the DPSI Micro DualBat. The DPSI Micro DualBat dual power supply must be connected with the "RV OUT" output to the DPSI BUS HUB input "BAT".

The listed DPSI Bicro DualBat dual power Supplies are suitable for operating the DPSI BUS HUB:

  • DPSI Mirco DualBat 5.5V/5.9V MPX-1xMPX
  • DPSI Mirco DualBat 5.9V/7.2V MPX-1xMPX

In addition to the safety-related dual power supply the DPSI Micro DualBat allows operating with a regulated input voltage of 5.5 volts, 5.9 volts or 7.2 volts. The DPSI BUS HUB can be switched on and off with the magnetic switch integrated inside the DPSI Micro DualBat.

The DPSI BUS HUB connected with the DPSI Micro DualBat is recommended for R/C models with up to approx. eight servos at a permanent current of approx. 4 ampere.

Dual power supply with the DPSI Ampere

For operating the DPSI BUS HUB with a DPSI Ampere and two monitored batteries two batteries must be connected to the battery inputs "Battery 1" and "Battery 2" of the DPSI Ampere. The DPSI Micro DualBat dual power supply must be connected with the "Vout" output to the DPSI BUS HUB input "BAT".

In addition to the safety-related dual power supply the DPSI Ampere allows switching on and off the DPSI BUS HUB with the magnetic switch integrated inside the DPSI Ampere.

If an additional voltage regulation is needed optionally the voltage regulator DPSI Voltage can be used. The DPSI Voltage must be connected to the DPSI Ampere's "Vout" and "Charge" connectors, the DPSI Voltage's "Reg. out" output must be connecetd to teh DPSI BUS HUB's "BAT" input. With the jumper "Reg. out" a regulated input voltage of 6.0 volts, 6.6 volts or 7.2 volts can be selected.

Specifications

Table 2: Specifications DPSI BUS HUB
Input voltage 6V - 8.4V (5 NiMH or 2S Li++)
Output voltage (regulated for RX output) 5.9V
Ampacity (RX output) Permanent 2A, Peak 10A @ 2S LiPo battery
Output voltage (unregulated for servos) Identical to the input voltage
Ampacity (unregulated output) Permanent 8A, Peak 16A
Power-on control LED
Quiescent current approx. 3.5mA @ 7.4V
Max. amount servos 10
Dimensions 50mm x 39mm x 14mm
Weight approx. 86 Gramm