DPSI Remote switch actuator (Duplex)

From Hacker Motor Wiki
Revision as of 08:35, 15 January 2016 by Admin (talk | contribs) (First start-up)
Jump to: navigation, search

Product description

DPSI Remote switch actuator (Duplex)

The DPSI Remote switch actuator (Duplex) is a switch actuator suitable for DPSI dual power supplies that can be used with Jeti Duplex systems. The DPSI Remote switch actuator (Duplex) is composed of the Jeti Duplex RCSW RC switch and the EMCOTEC RCSW adapter. Using the DPSI Remote switch actuator (Duplex) DPSI dual power supplies can be switched on and off with the transmitter.

Variants and delivery contents

The DPSI Remote switch actuator (Duplex) is composed of above-named the modules. Certainly the EMCOTEC RCSW adapter can also be purchased stand-alone when a existing Jeti Duplex RCSW RC switch should be upgraded. So the DPSI Remote switch actuator (Duplex) is available in two variants:

Table 1: Variants of the DPSI Remote switch actuator (Duplex)
Variant Description
RCSW adapter Contains a single EMCOTEC RCSW adapter for upgrading an existing Jeti Duplex RCSW RC switch.
RCSW adapter with RCSW Contains an EMCOTEC RCSW adapter and a Jeti Duplex RCSW RC switch.
Delivery contents variant RCSW adapter: 1. EMCOTEC RCSW adapter
Delivery contents variante RCSW adapter with RCSW: 1. EMCOTEC RCSW adapter, 2. Jeti Duplex RCSW RC switch


Compatibility

The DPSI Remote switch actuator (Duplex) is compatible with the listet DPSI dual power supplies:

Notice

  • The DPSI Remote switch actuator (Duplex cannot be used with the dual power supply DPSI Ampere.
  • The DPSI Remote switch actuator (Duplex) can only be used with Jeti Duplex systems. Usage with other manufacturer's systems is not possible.

First start-up

Before the DPSI Remote switch actuator (Duplex) can be used it must be set up once. Therefor the following procedure is necessary:

  1. Bind Jeti Duplex RCSW RC switch to the system without connected to the EMCOTEC RCSW adapter.
  2. Connect batteries to the DPSI dual power supply.
  3. Connect EMCOTEC RCSW adapter to the DPSI dual power supply's switch actuator connector without the Jeti Duplex RCSW RC switch. The DPSI dual power supply switches on automatically.
  4. Connect the Jeti Duplex RCSW RC switch to the EMCOTEC RCSW adapter. The DPSI dual power supply switches off automatically (due to the Jeti Duplex RCSW RC switch is in "OFF" status).

The DPSI dual power supply can now be switched on and off with the DPSI Remote switch actuator (Duplex).

Find details concerning connecting the DPSI Remote switch actuator (Duplex) in chapter Connections.

Notice

  • The option Inverse polarity in the Jeti Duplex RCSW RC switch menu must be deactivated. Otherwise the Jeti Duplex RCSW RC switch cannot be used with the EMCOTEC RCSW adapter.
  • For operating the DPSI Remote switch actuator (Duplex) a minimum battery voltage of 7 volts is necessary. At a lower voltage switching on is not possible. So only batteries with a nominal voltage of 7.2 volts or 7.4 volts (e. g. LiPo or LiIon batteries) can be used.
  • If the receiver batteries were disconnected the steps of the chapter First start-up must be made again to operate the DPSI Remote switch actuator (Duplex).

Connections

The Jeti Duplex RCSW RC switch must be connected to the EMCOTEC RCSW adapter's right bottom side. The polarity is indicated on both modules. At the Jeti Duplex RCSW RC switch the connector Control Output must be used. The EMCOTEC RCSW adapter must be connected to the DPSI dual power supply's switch actuator connector.

Jeti Duplex RCSW RC switch at the EMCOTEC RCSW adapter: 1. top side, 2. bottom side
Conntectino of DPSI Remote switch actuator (Duplex) e. g. at the DPSI 2018 Duplex Edition