Difference between revisions of "DPSI RV Mini"
(→Output voltage selection) |
(→Battery types) |
||
Line 97: | Line 97: | ||
==Batteries== | ==Batteries== | ||
===Battery types=== | ===Battery types=== | ||
− | + | The following battery types can be used: | |
− | * NiCd | + | * 5S bis 7S NiCd |
− | * | + | * 5S bis 7S NiMH |
− | * | + | * 2S LiIon |
− | * | + | * 2S LiPo |
− | * | + | * 2S LiFePO4 |
===Battery programming=== | ===Battery programming=== |
Revision as of 09:39, 6 July 2018
Contents
Product description
The DPSI RV Mini is a [Dual power supply]] with electronic switch, servo current distribution and servo signal distribution. Depending on the version to the DPSI RV Mini 5 respectively 6 receiver channels can be connected on the input side and 7 respectively 8 servos can be operated on the output side. The Magic version of the DPSI RV Mini are equipped with and integrated servo matching technology. So center position, end positions and direction of the additionally connected servos at the output side can be adjusted.
Features
Feature | implemented |
---|---|
Electronic switch | Yes |
Dual power supply | Yes |
Voltage regulator | Yes |
Servo current distribution | Yes |
Servo signal distribution | Yes |
Servo matching | Yes (Magic versions) |
Versions
The DPSI RV Mini is available in five versions. These differ by the number of DPSI channels as well as the number of servo signal distributors or the servo match channels.
DPSI RV Mini 5
The DPSI RV Mini 5 has 5 DPSI channels to connect 5 receiver channels. The DPSI channels 1, 3 and 5 are servo signal distributors to connect each 2 servos at the output side. Both servos get the same receiver signal. With the DPSI RV Mini 5 8 servos can be operated on 5 receiver channels.
DPSI RV Mini 5 Magic
The DPSI RV Mini 5 Magic has 5 DPSI channels to connect 5 receiver channels. The DPSI channels 1, 3 and 5 are servo matching to connect each 2 servos at the output side. Both servos get the same receiver signal. One of the two servos acts as MASTER servo, the other one as SLAVE servo. The SLAVE servo can be electronically adjusted to the MASTER servo. With the DPSI RV Mini 5 Magic 8 servos can be operated on 5 receiver channels.
DPSI RV Mini 6
The DPSI RV Mini 6 has 6 DPSI channels to connect 6 receiver channels. The DPSI channel 6 is a servo signal distributor to connect 2 servos at the output side. Both servos get the same receiver signal. With the DPSI RV Mini 6 7 servos can be operated on 5 receiver channels.
DPSI RV Mini 6 Magic
The DPSI RV Mini 6 Magic has 6 DPSI channels to connect 6 receiver channels. The DPSI channel 6 is a servo matching channel to connect 2 servos at the output side. Both servos get the same receiver signal. One of the two servos acts as MASTER servo, the other one as SLAVE servo. The SLAVE servo can be electronically adjusted to the MASTER servo. With the DPSI RV Mini 6 Magic 7 servos can be operated on 5 receiver channels.
Delivery contents
DPSI RV Mini battery backer, switch actuator, patch cables.
Operating
Output voltage selection
The output voltage of the DPSI RV can be selected in two steps for the receiver and for the servos. This can be done with the enclosed jumpers which must be plugged to the slot at the housing depending on the desired output voltage.
In the example the servos will be supplied with the full battery voltage, the receiver will be suppied with 5.9 volts.
Die following output voltages are possible:
Version | Output voltage receiver | Output voltage servos |
---|---|---|
DPSI RV Mini 5 / Mini 5 Magic | 5.9V or 5.2V | 5.9V or full battery voltage |
DPSI RV Mini 6 / Mini 6 Magic | 5.9V or 5.2V | 5.9V or full battery voltage |
DPSI RV Mini 6 bavarianDEMON Edition | Full battery voltage or 6V | Full battery voltage or 6V |
Switching on and off
The DPSI RV Mini can be switched on and off by using the connected switch actuator. After switching on the DPSI RV Mini the LED of connected switch actuator as well as the red status LED at the DPSI RV Mini's housing. Shortly after the buzzer and the LEDs show the programmed battery type optically and acoustically. Then both LEDs change to permanent shining.
Main article: DPSI switch actuators
Batteries
Battery types
The following battery types can be used:
- 5S bis 7S NiCd
- 5S bis 7S NiMH
- 2S LiIon
- 2S LiPo
- 2S LiFePO4
Battery programming
Da die DPSI RV Mini über eine Akkuspannungsüberwachung verfügt, muss der verwendete Akkutyp einmalig programmiert werden. Der programmierte Zustand bleibt dann bis zu einer neuen Programmierung in der DPSI RV Mini gespeichert.
Die Programmierung wird gestartet, in dem nur ein Akku (egal, welcher Typ und an welchem Akkuanschluss) an die DPSI Micro RV Mini angeschlossen und diese dann eingeschaltet wird.
Sobald die Programmierung gestartet wurde, piept der Signalgeber für 3 Sekunden, dann erfolgt eine 3-sekündige Unterbrechung des Signalgebers. Dies zeigt an, dass sich die DPSI RV Mini im Betriebsmodus "Programmierung" befindet.
Nun gibt der Signalgeber der Reihe nach Piepsignale für die entsprechenden Akkutypen (siehe Tabelle 2) aus, gefolgt von jeweils 3 Sekunden Pause. Die roten LEDs auf dem Gehäuse und im angeschlossenen Schaltgeber blinken synchron zum Piepsignal.
Sobald der gewünschte Akkutyp angezeigt wird, muss der Programmiermodus innerhalb der 3-sekündigen Pause verlassen werden, bevor der nächste Akkutyp durch einen neues Piepsignal angezeigt wird. Der Programmiermodus wird verlassen, indem während der 3-sekündigen Pause zwischen den Piepsignalen und den Blinkcodes der zweite Akku angesteckt wird. Der gewählte Akkutyp wird gespeichert.
Blinkcode | Akkutyp | Nennspannung |
---|---|---|
1x Blinken | 5 NiCd/NiMH-Zellen | 6,0 |
2x Blinken | 6 NiCd/NiMH-Zellen | 7,2V |
3x Blinken | 2 LiIon-Zellen | 7,2V |
4x Blinken | 2 LiPo-Zellen | 7,4V |
5x Blinken | 2 LiFePO4-Zellen | 6,6V |
6x Blinken | 7 NiCd/NiMH-Zellen | 8,4V |
7x Blinken | Prüfungen deaktivieren | --- |
Bei der Auswahl „7x Blinken“ (Prüfungen deaktiviert) führt die DPSI Micro keine Spannungsprüfungen durch. Demnach werden keine leeren Akkus oder sonstigen Fehler mehr mitgeteilt.
Anschließen des Empfängers und der Servos
Der Empfänger wird mit den mitgelieferten Patchkabeln an den "RECEIVER INPUT"-Eingängen des DPSI RV Mini angeschlossen.
Die Patchkabel müssen mit der braunen Minusleitung nach oben, mir der orangen Impulsleitung nach unten angeschlossen werden.
Servo-Matching
Specifications
Power sources | 5 to 5 cell NiCD / NiMH batteries, 2 cell LiIon, LiPo, LiFePO4 batteries |
---|---|
Operating voltage range | 5.0V ... 13V |
Nominal input voltage | 6.0V ... 8.4V |
Output voltage receiver | 5.2V or 5.9V selectable by jumper |
Output voltage servos | 5.9V or full battery voltage selectable by jumper |
Quiescent current (switched off) | Approx. 1µA per battery |
quiescent current (switched on) | Approx. 55mA (Magic versions approx. 70mA) |
Max. permanent current @ 5.9V (15 minutes with LiPo batteries) | 5A |
Max peak current @5.9V | 50A |
Drop out loss @ 4A | 0.4V |
Maximale Verlustleistung (Dauer) | 8W |
Amount of servos inside system | Up to 10 servos |
CE approvals | according to 2004/108/EC |
Environmental conditions | -10°C ... +50°C |
Permissible temperature range | -25°C .... +85°C (Storage) |
LCL filtering (EMI) | For each individual servo output |
nterference Suppression at 35MHz | -20dB @ 35MHz, -34dB @ 100MHz |
Dimensins | 77mm x 99mm x 15,8mm |
Weight | Ca. 105g |